Cheapest DIY Stainless Cable Deck Railing Pt.4: INSTALLATION - Running the cables through the posts




Part 4 in my series on installing stainless cable deck railing on the cheap. In this video, I show how to install the stainless cable after the post holes are drilled. This covers running the cable, cutting to length and crimping the hardware.


These are the crimping and cutting tools that I use:

  1. Titan 11980 Hydraulic Cable Crimper - This tool comes with a large set of dies, so I will be able to use it in the future for crimping electrical connectors and swaging cables. Cable railing retailers will rent crimpers, but the rental cost is as much as buying this tool.

  2. Cable Cutters - I recommend the larger 13" to 18" cutters, like these for ease of cutting. Most of the cable sellers on Amazon are trying to sell the small cable cutters, like these. However, I do not recommend these small cutters, because I found them to be very difficult to cut the 1/8in 1x19 cable without pinching your fingers. I think the larger strands make it difficult to cut.


This is the stainless cable deck railing hardware that I purchased.

This was the cheapest price that I could find and appears to be the same quality as the hardware sold by other brands on Amazon.


Total Cost for hardware was only $425.74 which is $1000's less than buying from cable railing retailers. The main savings are the cable terminals. Cable railing retailers sell their terminal sets at prices upwards of $10-$15 a pair. The ones I bought cost less than $2 a pair. That adds up quickly when you have a lot of deck corners that weren't designed for cable railing, and therefore need to terminate the cables at each corner.


Most Amazon stainless cable sellers are selling the 7x7 1/8in cable instead of the 1x19 configuration. The 1x19 is preferred for cable railing because it has larger individual strands. That makes it more rigid, stronger, and more aesthetically pleasing. It was more difficult to find, but I finally found this high quality, made in Korea, stainless 1x19 1/8in cable. https://amzn.to/3hgJFTM It only cost $220 for 1000 ft, making it $0.22 per foot, which is less than half the price that cable rail retailers want to sell their cable!


Additional installation tools that I had to buy:

- Titan 11980 Hydraulic Cable Crimper https://amzn.to/2DPUptF - This tool comes with a large set of dies, so I will be able to use it in the future for crimping electrical connectors and swaging cables. Cable railing retailers will rent crimpers, but the rental cost is as much as buying this tool.

- Cable Cutters - Most of the cable sellers on Amazon are trying to sell the small cable cutters, like these: https://amzn.to/2WKvcHA However, I found those to be very difficult to cut the 1/8in 1x19 cable without pinching your fingers. I think the larger strands make it difficult to cut. Therefore, I would recommend the larger 13" to 18" cutters, like these: https://amzn.to/32PBCtb


- Cable Tension Gauge - Although not absolutely necessary, it will help you tighten the cables consistently to all the same tension. 1/8in stainless cables have to be tensioned between 150-300lbs to prevent a 4-inch sphere from passing between the cables. The tension required to meet that specification will vary depending on the spacing of the posts.




These are tools that are used to drill the wood posts.

Details can be seen in this Video Pt.3:

- Wolfcraft 4525404 Multi-Angle Drill Guide: https://amzn.to/3fMw2v5 - IRWIN QUICK-GRIP Bar Clamp, One-Handed, Medium-Duty, 12-Inch: https://amzn.to/2CSC6nq - Ryobi 18V Cordless Brushless Drill: https://amzn.to/39dsFef - 1/4in Diameter by 12in Long Drill Bit - A standard drill bit can barely make it through a 4in post. The longer drill bit is neccessary when drilling at an angle, like for posts on the staircase.


Check out the whole series of stainless cable railing videos in this playlist: https://www.youtube.com/playlist?list=PLJZvr9eL7PeyHeBj51cTain6uAiDfz9lX


Video Timeline 0:00 - Intro 0:03 - Running The Cable Through Post Holes 0:37 - Crimping The Stemball Dead End 1:43 - Finishing The Dead End 2:01 - Measure And Cut Cable 3:00 - Crimp the Threaded End 3:56 - Finishing the Threaded End 4:15 - Conclusion 5:16 - Watch the other Videos https://www.youtube.com/playlist?list=PLJZvr9eL7PeyHeBj51cTain6uAiDfz9lX


#deck #cable #rail #stainless #diy

The products shown here were purchased by me with the intent to use. I did not receive any free items, and I am not being paid or compensated for this review. The video and description may contain affiliate links. If you click on a link, I may receive a commission. Money earned helps to support my channel and bring you more informative videos about engineering, crafting, and DIY.

Categories
Recent Posts
Search By Tags
Follow Us
  • Facebook Basic Square
  • Twitter Basic Square
  • Google+ Basic Square

© 2018 by Engineerable.

  • Grey Facebook Icon
  • Grey Twitter Icon
  • Grey YouTube Icon
  • Grey Pinterest Icon
  • Grey Instagram Icon